常见问题

General Operation

  1. 确认设备连接正确(USB电缆已插入设备和计算机).

  2. 确认USB电缆没有任何损坏.

  3. 确认设备有足够的电池寿命(不适用于GC2T / HMT / Kiosk)。 要检查GC2电池的当前电量,请使用显示屏上的LCD键盘,按最左箭头键,然后导航到显示设置菜单中的“关于”菜单屏幕。当前电池电量将以伏特为单位显示。 GC2的镍金属氢化物电池被认为在7.6伏或更高电压下完全充电。 如果显示7.1伏或更低的读数,则需要对电池进行充电。

    如果问题持续存在

  4. 将GC2设备插入Windows计算机并打开电源时,请转到计算机的START MENU> 设备和打印机并向下滚动到未指定的设备,并查看是否" NGLM MSC接口设备 " 被展示。 如果 "NGLM MSC接口设备"显示并显示没有相关的错误,您的计算机可以识别GC2设备,问题可能是您的闪存模块或正在使用的USB电缆的长度。 推荐的USB电缆长度不应超过5米/ 16英尺。 请联系Foresight Sports技术支持以获取帮助

    要确认Windows计算机上已正确安装设备驱动程序,请按照下列步骤操作:

    1. 转到START控制面板程序程序和功能
    2. 通过查找名为的应用程序,确保已安装驱动程序"Windows驱动程序包 - Foresight Sports(WUDFRd)"
    3. 如果此文件存在,则已正确安装驱动程序.
    4. 如果此文件不存在,请从Foresight Sports DOWNLOADS页面下载驱动程序并完成安装过程.
  5. 如果问题仍然存在,则可能是USB输入或USB电缆出现问题。 尝试将USB电缆移动到计算机上的其他USB端口。 如果仍无法解决问题,请尝试使用其他USB电缆连接设备.

如果GC2在未直接插入电源时仍未保持通电状态.

  1. 如果设备在未插入AC适配器时立即关闭,则可能存在电池问题.
  2. 首先,请先确认电源适配器是否正常工作。 Foresight Sports提供的电源适配器包括一个绿色LED灯,如果正确接通电源,它仍会点亮。 如果在操作过程中绿灯未亮起,则说明适配器无法正常工作。 请联系Foresight Sports技术支持部门以获取更换适配器。
  3. 如果电源适配器工作正常,请将设备连接到交流电源12小时,以便为电池充电。 要检查GC2电池的当前电量,请使用显示屏上的LCD键盘,按最左箭头键,然后导航到显示设置菜单中的“关于”菜单屏幕。当前电池电量将以伏特为单位显示。 GC2的镍金属氢化物电池被认为在7.6伏或更高电压下完全充电。 如果显示7.1伏或更低的读数,则需要对电池进行充电.
  4. 如果在执行上述步骤后,设备在断开电源时未保持充电状态,则表示电池不再保持充电状态。 有关更换电池的详细信息,请联系Foresight Sports技术支持.

闪存模块是需要偶尔更换的项目。 如果您的设备无法识别镜头(显示破折号)或显示不一致的读数,则可能需要更换GC2上的闪光设备.

  1. 将设备从任何防护罩中取出并放置在水平地板上,并正确设置支脚/闩锁以确保正确操作.

  2. 在尝试诊断闪存模块之前,请按住电源按钮6秒(直到设备关闭电源)并再次重新启动设备,确认设备未受到静电冲击。.

  3. 将GC2放在与球相同的水平面上。 放置在击球区域时确认设备识别球(如绿色指示灯所示)。 继续击球.

       >  如果设备显示 DASHED READINGS, 设备正在工作,但需要更换闪光灯。 请按照GC2用户手册中的说明更换闪光灯.

       >  如果是设备 DOES NOT RECOGNIZE BALL, 请参阅标题为“GC2设备无法识别球/不定读数的部分”.

  4. 如果在查阅这两个故障排除步骤后GC2仍然没有响应镜头,请联系Foresight Sports技术支持.

屏幕数据

  1. GC2设备完全打开电源后,选择前LCD面板上最左侧的箭头按钮.
  2. 要选择选项,请使用向上和向下箭头键导航。 要选择所需的测量单位,请按“确定”按钮,直到出现设置.
  3. 选择所需的测量单位后,再次按最左箭头键返回球查找/播放模式.
  4. 您的新设置已保存,现在将在播放期间显示.
  1. 确认设备已完全打开且脚/闩锁正确放置在下方.

  2. 确认设备放置在与球相同的水平面上.

  3. (如果适用)确认防护罩(附件)已正确安装且不妨碍摄像机或球形锁定窗.

  4. (如果适用)连接到运行Foresight Sports FR1或FSX软件的Windows计算机时,确认在数据选择设置下启用了“等待旋转”.

  1. 使用新的闪存模块(或您确定正在运行的模块)测试设备。 这将有助于确定闪存模块是否是问题的真正原因.

  2. 如果闪光灯模块工作正常,请参阅下面的“球找不到的镜头”.

  3. 如需购买额外的闪存模块,请联系Foresight Sports技术支持.

球发现错过的射门

  1. 屏幕上的球放置辅助工具仅在设备寻找球时显示(“球锁”指示灯将闪烁红色)。 球必须放置在右侧或左侧击球区域(由梯形表示),以便发生球锁.

  2. 一旦GC2锁定在球上,“球锁”指示灯将变为稳定的绿色,表示球现在可能被击中.

  3. 光模式和相应的含义:
    慢速(红色)闪烁:表示设备正在寻找球
    快速(红色)闪光:球发现区域外的指示球必须朝向框的中心移动
    SOLID GREEN:表示球已被识别且设备已准备好使用.
    交替(红色/绿色)闪烁:表示检测到球但设备无法建立锁定

  4. 注意:当锁定在球上并通过USB线连接到运行FR1或FSX软件的Windows计算机时,Foresight Sports徽标将出现在LCD屏幕上.
    当锁定在球上而未连接到Windows计算机时,之前的拍摄数据将出现在LCD屏幕上.

  1. 确认球出现在LCD显示屏的击球区域内.

  2. 确认设备已完全打开且脚/闩锁正确放置在下方.

  3. 确认设备放置在与球相同的水平面上.

  4. 确认没有阻碍球的能见度(如高草)

  5. (如果适用)确认防护罩(附件)已正确安装且不妨碍摄像机或球形锁定窗.

  6. 在右手和左手位置测试GC2。 如果任何球放置区域未能产生球锁,请联系Foresight Sports技术支持.

  1. 关闭GC2设备的电源。 如果连接到计算机,请断开USB线.

  2. 等待5-10秒再重新打开设备电源。 此时请勿将USB电缆插入GC2.

  3. 在左侧或右侧击球区域放置一个球

  4. 如果设备成功锁定球,如实心绿灯所示,但球击后不显示数据,请参阅主题:“确定何时需要更换闪存模块”.

FR1软件

根据数据的性质,可以在仿真软件中保存多种文件类型(和位置):

  1. 俱乐部配件数据:
    通过选择屏幕底部的“SAVE CSV”按钮,可以在SHOT ANALYSIS屏幕的底部保存球杆配件数据.
    要访问已保存的文件,请转到Windows计算机的本地驱动器“程序文件”(如果使用64位计算机,则转到“程序文件(x86)”)Foresight FITTING文件夹。 可以使用MS Excel或类似程序打开该文件.

  2. 视频重播
    完成拍摄后,从MENU中选择VIEW REPLAY。 SAVE REPLAY选项作为屏幕底部的按钮提供.
    要访问保存的文件,请转到Windows计算机的LOCAL DRIVE“程序文件”(如果使用64位计算机,则转到“程序文件(x86)”)Foresight REPLAYS文件夹.

  3. 截图
    要截取屏幕截图,请同时按住CTRL和F8键以捕获屏幕上的图像.
    要访问已保存的文件,请转到Windows计算机的LOCAL DRIVE“程序文件”(如果使用64位计算机,则转到“程序文件(x86)”)Foresight SHOTS文件夹.

关键的中风 行动
Left Arrow Aim Left
Right Arrow Aim Right
Q Raise above landscape
A Return to course elevation
   
GAME MODE  
A Display gap fitting results
   
FITTING MODE         
Left Shift Kneel to see break
G Toggle grid
F8 Screen capture (image)
R Record fly-by (video)
I Recall shot information
P Split screen shot information
F6 Remove UI
ESC Exit
Space Bar Accelerate ball flight to get Shot Data Screen quicker
   

注意:多个播放器只是正常游戏的选项; 它不是“PRACTICE”或“FITTING”模式的选项.

  1. 要在游戏模式中选择第二个玩家,请双击右侧菜单中的玩家名称.
    播放器将作为选定的配置文件显示在左侧菜单中.

  2. 要创建新播放器,请选择“创建播放器”并填写所需的配置文件信息.

电脑

Desktop System  
Operating System: Windows 7 (64 bit or greater)
Memory: 4Gb RAM or greater
Processor: 2.4 Ghz or greater (Recommended: i5 Series)
Video Card: 2GB of memory with memory bandwidth per second > 75 GB/sec; (Recommended: Nvidia 750Ti or greater)
  If you have questions please contact your Foresight Sports Sales Representative.
   
 

注意:使用不符合要求的计算机可能会损害软件的运行能力,并可能损害软件的最佳运行能力。 如果您有兴趣购买模拟优化的台式机或笔记本电脑,请联系我们的销售人员.

注意:如果您在运行Foresight运动模拟软件时遇到问题,请在尝试重新加载软件之前确认计算机符合本节“计算机要求”中指示的最低规格。.

为确保正确加载软件,请按照下面的安装说明进行操作.

如果先前已安装该软件,请在现有版本上运行此更新。 请勿卸载当前安装的任何课程包.

  1. 启动“Foresight Sports FR1 Components”安装文件.

  2. 单击“下一步”按钮并接受条款和条件协议以继续。

  3. 确保在继续之前选择所有三个组件GC2 Driver,DirectX和Adobe Reader

  4. Once the GC2 driver installation has begun, accept the agreement and select the appropriate operating system from the list.

  5. Allow the Adobe Reader and DirectX installations to run, and accept the Microsoft License Agreement

  6. Now the Foresight Setup Wizard will run, press Next to proceed. Do NOT change the installation location.

  7. Select the check box to create a Desktop Icon

  8. Select Finish when prompted to complete the Setup Wizard.

  9. Lastly, setup will run the Simulator Setup Tool. Follow the on screen diagram and instructions to measure the hitting environment. Recommended: Measurement should be done with inches for best accuracy. Select Save Settings when complete.

  10. If NOT using a projection screen system, enter the default settings as shown below:
    Image Width: 16ft
    Image Height: 9ft
    DZ: 11ft
    DX: 1.5ft
    DY:  0ft
    Azimuth: 0ft

  11. On the final window, press Finish to complete the installation.

  12. Insert the green FR1 USB dongle (provided with your software purchase) into the computer. Allow a moment for the computer to load the necessary driver for the dongle to function.

  13. The FR1 Quick Start Guide has been dropped onto the desktop of the computer to assist with any questions that may arise regarding use of the software.

  14. To launch your software, select the “Foresight” icon on your desktop.

投影机图像

  1. From the MAIN MENU, go to the OPTIONS MENU at the top of the screen.

  2. Enter the password "fss01011" to gain access and go to the graphics menu.

  3. Set the BRIGHTNESS to 0.81 and the CONTRAST to 1.40.

  4. SAVE the applied settings and restart the game. The projected/onscreen image should now be normal.

The projected image may not fill your screen if the resolution is set incorrectly. To correct this:

  1. Right-click on the desktop and find “Screen resolution”.

  2. Select the projector from the options offered and change the resolution. NOTE: Make sure that the new resolution setting is within the recommended resolutions for the projector or monitor being used.

  3. If the projector is still not filling out the screen as desired, confirm that your projector is mounted the correct distance from the screen. DO NOT CHANGE IN-GAME RESOLUTION settings without first changing resolution settings on your computer to insure compatibility with the projector.

Because all projectors are designed to be mounted to a ceiling (inverted) or placed on a level surface, they have a built-in function that allows the image to be flipped to accommodate either orientationn. To correct a flipped image:

  1. Go to your projector’s MENU screen (location varies depending manufacture and model) and locate the SETTINGS option.

  2. Within the screen settings, select or de-select “Ceiling” mode as needed.

  3. Save the setting (if needed). The on-screen image should now be correctly oriented.

Confirm that the computer is properly connected to the monitor and/or projector. Foresight Sports recommends using the same connection-type (such as DVI) if connecting to two monitors or a projector.

  1. Once you've confirmed that the monitor and/or projector is properly connected, right-click on the computer desktop and select SCREEN RESOLUTION.

  2. If the monitor and/or projector is powered on, it will show as a selectable screen to display the image. If the monitor/projector is not seen here, click “detect” in the upper right near the image of the screens. This will allow the computer to recognize the screen.

  3. If not detected, please contact your computer manufacturer.

  4. Once the monitor and/or projector has been detected, start the FR1 software.

  5. Go to the OPTIONS menu and enter the password “fss01011”.

  6. Go to SCREEN SETTINGS and set the resolution for the monitor you are using to match the resolution set on your computer. Confirm that the game is presenting to the correct screen (select from the available monitors seen in the screen settings menu). This will allow the simulation software to run correctly.

如果收到错误消息,请参阅本节中的“投影仪或监视器错误消息”区域.

  1. With FR1 Software NOT running, confirm that the computer is recognizing the projector and/or monitor in the screen resolution screen, accessible by right clicking the desktop. If not, please refer to the “blank screen during game startup" area of this section.

  2. Confirm that the projector and/or monitor are set to the recommended screen resolutions. This can be discovered by reviewing the user manual for the given projector or monitor. It is also highly recommended that the same type of inputs for all displays be utilized (HDMI, DVI, VGA, etc.).

  3. A "Direct 3D" error message indicates that the software is not properly configured to run on the selected game monitor or projector.

If this occurs:

  1. Disconnect (including any adaptor) the projector or monitor that is producing the error from the computer.

  2. Restart the computer running only the properly working projector or monitor.

  3. Restart the FR1 software.

  4. If the error occurs again, repeat the above process but use the other monitor or projector this time.

  5. Once the FR1 software is running, go to the OPTIONS menu at the top of the MAIN MENU screen and enter the options screen using the password "fss01011".

  6. Go to the “Screen Settings” and select the recommended screen resolution for the current projector or monitor (This can be found in the user manual from the projector or monitor). Select the monitor or projector.

  7. Run the game to confirm that the monitor or projector is working correctly.

  8. Exit the game.

  9. Re-connect the other monitor or projector to the computer. Right-click on the desktop and go to the Screen Resolutions settings. You should see the two screens both plugged into the computer at this point. If not, select “detect” in the upper right of the screen, the computer may not identify the new display. Once both screens are recognized by the computer confirm that both are set to the manufacturer's recommended resolutions.

  10. Go back into the game, go to the OPTIONS menu at the top of the MAIN MENU screen and enter the options screen using the password "fss01011".

  11. Go to the "Screen Settings" and select the second monitor/projector

  12. Change the resolution to match the recommended screen resolution. You can try to set the game to show on the projector at this point.
    If the game still will not show on the screen at this point, change all settings to the lowest resolution settings (800x600 resolution).

  1. Confirm that your Windows computer meets the minimum SYSTEM REQUIREMENTS stated above.

  2. Confirm that no other software is running while attempting to run the FR1 software, as this may slow performance.

  3. If the computer meets the proper system requirements, check the graphic settings. This can be done by going into the OPTIONS menu at the top of your MAIN MENU screen in the FR1 Software. Enter the password "fss01011" to gain access. In the Graphics option, go to the top of the screen and reset the graphics settings to "balanced". If already set to "balanced" change to "minimum".

  4. If this still does not resolve the problem, we recommend installing the latest update to the software in the Downloads section.

Connections

  1. On your Android device, go to the SETTINGS menu and select WIRELESS CONNECTION

  2. In the BLUETOOTH manager, turn Bluetooth on.

  3. While the GC2 is turned on, locate the SERIAL NUMBER of the device (located on the label underneath). Select the device with that SERIAL NUMBER to pair with it. If prompted for a code, enter four zeros (0000).

  4. Open the Foresight Sports Performance app. Locate the GC2 device you wish to connect to and press and hold until “CONNECT” appears. NOTE: Connection times vary by device.

The device should now be successfully paired and connected to the Foresight Sports Android Application.